Product Search

Advanced Search


Glass Etching Products
Armour Etch Cream
Glass Etching Kits
Etch Bath

Glass Etching Stencils
Designer Rub'N' Etch Stencils
Rub'N' Etch Stencils
Closeout RNE Stencils
Peel 'N' Etch Stencils
Over 'N' Over Stencils
Stencil Material
Made-To-Order Stencils
Made-To-Order Monograms
Custom Wedding Glass Stencils

Glass & Stencil Packs

Sand Etch
Sand Etch Kits
Sand Etch Stencils
Sand Etch Refills
Inflate 'A' Booth

Bottle & Jar Cutter

Books
Stencil Books
CD Stencil Books
Instructional Books

Glass Engraving

Cutting Supplies

Glass
Glass Shapes
Glass & Stencil Packs
Thin Beveled Glass
Thick Beveled Glass
Tableware
Heavy Glass
Trays & Platters
Mirrors
Vases
Glass Bottles
Craft Glass Objects
Glass Picture Frames
Glass Diamonds

Sand Blasting
Sand Blasters
Smaller Size Sand Blasters
Abrasive
Replacement Sand Blaster Parts
Sand Blasting Resist

Craft Supplies


Closeout Specials

Web Specials

Secure Online Payments

Glass Etching Kit Instructions



Glass Etching Kit Instructions
click on picture to download
size: 1.1 MB

French Instructions

Spanish Instructions



The Basic Glass Etching instructions :

Getting To Know the Glass Etching Kit

Clean the glass or mirror

1. Clean the glass or mirror thoroughly to remove all grease, dust and fingerprints. Avoid cleaner solutions that advertise Finger print resistant, as these cleaners leave a film on the glass that hinders the etching process. Avoid finger prints on the glass where you are going to etch. Dry glass or mirror completely

Selecting stencil design & applying to glass

2. Choose the design of your choice and carefully cut the stencil sheet and the frosted backing sheet together to avoid touching the back side of the stencil sheet.Measure carefully to determine where you will locate the stencil on the glass or mirror. Separate the blue stencil sheet from the frosted backing sheet. Put aside the frosted backing sheet to be used later. Place stencil sheet on the glass with the blue (tacky) side touching the glass. Secure stencil sheet temporarily to the glass with masking tape.

3. Using the wood stick enclosed, transfer the stencil from the sheet to the glass surface by rubbing firmly over the design with smooth, even strokes. Rub left and right, then up and down. Do not dig into the stencil. You will be able to see the stencil being transferred by the change in color from a dark blue to a lighter blue. Be careful when you rub near the edge of the stencil not to peel it back up by accident.

Remove top carrier sheet

4. When the entire stencil has been adhered, carefully remove some of the masking tape and slowly peel back the clear top sheet. If the stencil has not been totally adhered to the glass, put the top sheet back down and re-rub area until all pieces are adhered.

Preparing the glass for etching

5. Apply a border of masking tape around the entire stencil overlapping the tape on the blue stencil by 1/16" to 1/8", being careful not to overlap the design.This overlap prevents the etching cream from contacting the glass and etching unwanted areas! If a very large area of glass needs to be protected, use strips of adhesive backed shelving vinyl. When all sides of the stencil have been taped, use the white frosted backing sheet to lightly rub over the entire stencil area. Check the stencil for small tears or holes by holding the project up to the light. If any holes appear, cover them with small pieces of tape. Be careful where you put the tape, because the stencil will tear if you try to remove it.

Applying the Armour Etch cream

6. For best etching results we recommend that the room temperature, the etching cream temperature and the object you are etching be over 70 degrees. Shake the ARMOUR ETCH Cream thoroughly. Work in a well lighted and well ventilated area near a water source. Wear plastic gloves and protective eye-wear. You must apply a thick layer of etching cream in order for the chemical to react properly on the glass or mirror. Thick enough so that you cannot see the design of the stencil through the Armour Etch Cream. Stay within taped area.

Removing etching cream & stencil

7. Allow ARMOUR ETCH Cream to remain on glass for one minute only.. No longer! Immediately wash off all the etching cream under luke warm water. Some of the stencil will be removed during this rinse, but it?s OK. After all traces of the etching cream are washed away, remove all the remaining tape and stencil pieces. Clean the glass using window cleaner and dry completely.